We use cookies to make your experience better. To comply with the new e-Privacy directive, we need to ask for your consent to set the cookies. Learn more.
AVTECH Firmware Updates September 2017
New releases of AVTECH Room Alert firmware for the Room Alert 3E, the Room Alert 4E / 4ER, Room Alert 12E / 12ER and the Room Alert 32W.AVTECH Software have released a number of firmware updates for the Room Alert 3E, Room Alert 4E / 4ER, Room Alert 12E / 12ER and Room Alert 32W.
| Product | SKU | New Firmware Version |
|---|---|---|
| Room Alert 3E | RA3E-ES0-BAS | 2.1.0 |
| Room Alert 4E / 4ER | RA4E-ES1-WAS / RA4E-ES1-RAS | 4.1.0 |
| Room Alert 12E / 12ER | RA12E-TH1-WAS / RA12E-TH1-RAS | 3.1.0 |
| Room Alert 32W | RA32W-WS1-RAS | 3.1.0 |
Room Alert 3E Changes
- Added support for AVTECH’s new Active Power Sensor
- Updated GoToMyDevices Push to send data to My.RoomAlert.com
- Resolved an issue that prevented the fourth output on a Relay Switch Sensor from being toggled via SNMP set commands.
- Added a setting to the ‘Security’ section of the telnet menu which can prevent Light Tower and Relay outputs from being toggled through the web interface.
- Added support for pushing data to GoToMyDevices.com immediately when a Light Tower or Relay output is toggled.
- Resolved an issue that could cause negative analog readings to appear incorrectly through SNMP queries.
- Added analog sensor OIDs to the MIB file.
- Updated SNMP support to properly scale decimal values for custom analog readings.
- Resolved an issue that could cause 0 volt analog readings to be incorrectly reported as 5 volts.
- Resolved an issue that could cause TCP discovery to get disabled when SNMP was disabled.
Room Alert 4E / 4ER Changes
- Added support for AVTECH’s new Active Power Sensor
- Updated GoToMyDevices Push to send data to My.RoomAlert.com
- Resolved an issue that prevented the fourth output on a Relay Switch Sensor from being toggled via SNMP set commands.
- Added a setting to the ‘Security’ section of the telnet menu which can prevent Light Tower and Relay outputs from being toggled through the web interface.
- Added support for pushing data to GoToMyDevices.com immediately when a Light Tower or Relay output is toggled.
- Resolved an issue that could cause negative analog readings to appear incorrectly through SNMP queries.
- Added support for pushing data to GoToMyDevices.com immediately when a ping changes states.
- Resolved an issue that could prevent the green check mark status icon from appearing on the web interface when a ping is up.
- Resolved an issue that could cause custom analog values to be slightly off in alert emails.
Room Alert 12E / 12ER Changes
- Added support for AVTECH’s new Active Power Sensor
- Updated GoToMyDevices Push to send data to My.RoomAlert.com
- Resolved an issue that prevented the fourth output on a Relay Switch Sensor from being toggled via SNMP set commands.
- Added a setting to the ‘Security’ section of the telnet menu which can prevent Light Tower and Relay outputs from being toggled through the web interface.
- Added support for pushing data to GoToMyDevices.com immediately when a Light Tower or Relay output is toggled.
- Resolved an issue that could cause negative analog readings to appear incorrectly through SNMP queries.
- Updated alerting process to send SNMP traps on alerts from the internal analog sensor.
- Resolved an issue that could prevent emails from sending when an alert on an internal analog sensor clears.
- Added the custom analog value to the SNMP tree.
- Resolved an issue that could cause switch sensor alarms to trigger relays when they were configured for ‘No Alarm Profile’.
- Resolved an issue that would prevent negative values from being entered into the ‘Scale High’ field for internal analog sensors.
- Resolved an issue that could cause custom analog values to be slightly off in alert emails.
Room Alert 32W Changes
- Added support for AVTECH’s new Active Power Sensor
- Updated GoToMyDevices Push to send data to My.RoomAlert.com
- Resolved an issue that prevented the fourth output on a Relay Switch Sensor from being toggled via SNMP set commands.
- Added a setting to the ‘Security’ section of the telnet menu which can prevent Light Tower and Relay outputs from being toggled through the web interface.
- Added support for pushing data to GoToMyDevices.com immediately when a Light Tower or Relay output is toggled.
- Resolved an issue that could cause negative analog readings to appear incorrectly through SNMP queries.
- Updated the web interface to allow ‘0’ to be saved for the number of enabled WiSH Sensors.
- Resolved an issue that could prevent emails from sending when an alert on a WiSH’s switch sensor clears.
- Resolved an issue that could prevent Light Tower / Relay actions from performing when an alert on a WiSH’s switch sensor clears.
- Added red/green status icons to the web interface to indicate the alert state for the internal temperature of WiSH sensors.
- Resolved an issue that could cause continuous emails to be sent when a sensor is disconnected from a WiSH sensor.
- Added the custom analog value to the SNMP tree.
- Resolved an issue that could cause adjust values on humidity sensors to display incorrectly after saving settings.
- Added support for toggling Light Tower and Relay outputs based on alerts configured for the internal power sensor.
- Resolved an issue that would prevent negative values from being entered into the ‘Scale High’ field for internal analog sensors.
- Disabled SNMP fields for WiSH sensors that are not connected.
Related Posts
-
AVTECH Product News for January 2015
It looks like it is going to be an interesting start to 2015 from AVTECH Software. Two very exciting new products are due to arrive shortly, both are likely to prove very popular with new and existing customers. -
AVTECH Room Alert 3 WiFi is now available
The AVTECH Room Alert 3 WiFi is now available and in stock. The Room Alert 3 WiFi is the new wireless version of the popular Room Alert 3E model. You can now extend your monitoring beyond the reach of your ethernet network. -
AVTECH Room Alert Planning Worksheets
Tailor an AVTECH Room Alert solution to your exact requirements with our new Planning Worksheets. Each Room Alert model page has a downloadable worksheet that shows you exactly the number and type of sensors which fit each Room Alert model. -
NEW - Longer Temperature sensors for all AVTECH Room Alert models
Now it's even easier to monitor distant locations with the longer Temperature sensors for the Room Alert models. Available in lengths of 15m and 30m.
Related Products
-
AVTECH Room Alert 12ER£630.60 £525.50 -
AVTECH Room Alert 3E£167.94 £139.95 -
AVTECH Room Alert 4ER£418.80 £349.00 -
AVTECH Room Alert 12E£598.80 £499.00 -
AVTECH Room Alert 4E£402.00 £335.00
Powered by Mirasvit Magento 2 Extensions
Recent Posts
-
Announcing End of Life for AKCP sensorProbe2, sensorProbe4 & sensorProbe8
-
Announcing the new AVTECH Room Alert 3S is now available
-
AVTECH announce End of Life for Room Alert 32E and Room Alert 12E/ER
-
Announcing the new AVTECH Room Alert 3S Monitor
-
Help Protect Against Water Leak Damage With the AVTECH Spring Flood Sensor Promotion!